Computing ⁽³⁶⁾

All this packet radio progressing around the place reminds me of a time long ago, pre-Internet where dial-up BBSs became the new thing in town. Back then I had a BBC Micro and a modem that ran at two speeds - I forget which now (will edit later!) and I persuaded my mum to get BT in to fit a socket rather than the hard-wired phone we had then. This let me plug the modem in. I used to use a BBS called ‘More Summer Wine’ plus one other but I forgot the name. Much of the activity back then is lost in the mist of time (or rather I just can’t remember) but sending and receiving mail was fun. BBS systems were all a part of the wider FidoNet. Mail would be routed between the various BBS systems, many of which only had the one telephone line and so would be inaccessible while that was happening. Indeed, they were mostly single user anyway, although if the sysop was there you could message them via the console of the BBS which was probably sitting in someone’s bedroom. I am reminded of the many times I would set the BBC and…

Well. Further to my previous post where all hope seemed to have gone out of the window I finally made progress today, but not the way I set out to. First off, I pulled a Raspberry Pi 4 from another project and sat the CaribouLite HAT on it. Next was a fresh installation of DragonOS. But this time it did open the ssh port - I've no idea why it did not before and note I am being unscientific here as I changed the Pi, but I am not going backwards. Then, time for install.sh... All seemed to go well but the software failed to compile completely. Searching on the errors I added #include to two source files, cariboulite/software/libcariboulite/src/CaribouLiteCpp.cpp and cariboulite/software/libcariboulite/src/CaribouLite.hpp. Stripping out all the 'apt's and 'depmod' from install.sh and running it again and the software compilation completed! I had already added and commented out the necessary lines in /boot/firmware/config.txt so a reboot was all that was needed to kick it into life. The driver was loaded - lsmod|smi showed this and also /proc/device-tree/hat now exists, both precursors to success according to the notes and YouTube videos. Running sudo SoapySDRUtils --find showed the card, and, finally (!), running SoapySDRServer…

I came across this via a post someone made somewhere - actually it might have been an email on a group. Anyway, with a tx/rx range top to 6GHz I thought, why not? It arrived quite quickly from Crowd Supply via Mouser with Crowd Supply charging the VAT but no other taxes on arrival. I duly mounted it on a spare Raspberry Pi 3B with a fresh Bookworm 64 bit OS and followed the installation instructions at https://github.com/cariboulabs/cariboulite but I always got various errors and never got to a working system. The errors were mainly surrounding the SMI driver and the kernel headers. There seemed no way round this one, and thus no working system. Following on from another complaint I downloaded and installed DragonOS, a 64 bit variant with lots of SDR utilities built in. Once installed, although the developer stated that ssh is available from first boot and does not need the usual empty ssh file it is not - the system does not open port 22 but does open the vnc port so I then had to find out which of my desktop systems has a vnc viewer as I never use it. When I found one…

I thought I was going mad today. I wanted to print some rails for the FT817 and I already had the sliced files on the SD card in the 3D printer. I selected the first (there are two, one is a mirror of the other) and told it to print. Nothing. Reset the printer and tried again. Nothing. Opening the SD card on the Mac showed the file to be 0 bytes, which is certainly was not as I had printed it before. Ok, copy it again and try again. Nothing! Right. Delete all the files on the SD card - I have them all on the Mac anyway. Copy just the files for the rails across and try again. Nothing! Looking at the SD card via a terminal window - I must admit to be my favourite UI - it was full of all sorts of junk. Going duff perhaps? Ok, use a recycled 8Gb micro-SD in a holder, delete all the files currently on it, copy the rails across and try that. Ah, the files did not delete so it's full of old junk and I can't spot the files to print. Back to the Mac. Tried 3…

Here is the setup for GB7RVB, not much to see really. The radio is a Tait TM8110 which has been configured according to information on the OARC wiki. The NinoTNC is next to it, both currently sitting on top of my Portsdown. Above, and annoyingly not square because I need to move some cables, is the Pi 4 which is PoE powered from a Netgear switch.